Open Access
Numéro
Oil Gas Sci. Technol. – Rev. IFP Energies nouvelles
Volume 75, 2020
Numéro d'article 60
Nombre de pages 6
DOI https://doi.org/10.2516/ogst/2020053
Publié en ligne 11 septembre 2020

© R.A. Mathew & M. Abraham, published by IFP Energies nouvelles, 2020

Licence Creative CommonsThis is an Open Access article distributed under the terms of the Creative Commons Attribution License (https://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

1 Introduction

Black carbon produced by flaring of oil spill has strong implications for climate change. It is short-lived with strong warming potential that can cause climate change. It absorbs sunlight more than it reflects which results in faster melting of ice caps. It also accounts for a quarter of observed warming and remediating the oil spill quickly is a means of mitigating the effects of climate change. Oil can be introduced into the ocean by natural, accidental and/or intentional spills.

Bioremediation employs microbial metabolism in the optimal environment with adequate nutrients to breakdown contaminants. Bioremediation is the process that utilizes bacteria, fungi and/or green plants to naturally remove contaminants. The two approaches to bioremediation are biostimulation and bioaugmentation. Zobell (1973) states that bioaugmentation is the introduction of bacteria to a spill site to supplement the indigenous microbial population in digesting the spilled petrochemicals. The other approach is biostimulation which is the introduction of nutrients and/or other growth enhancing substances to a spill site for the growth of indigenous microbes in order to accelerate the digestion of the spilled petrochemicals. The important factors influencing the efficiency of bioremediation are the type of microorganisms present in marine water, characteristics of the oil such as chemical composition, sorption, bio-availability, concentration and environment surrounding the spill such as moisture content, pH, temperature and nutrients.

According to the Office of Technology Assessment (OTA), mechanical methods typically recover not more than 10–15% of the oil after a major oil spill (OTA, 1990). Unless the oil spill is contained in a boom it can drift very fast. Bioremediation is a promising technology for oil spill clean-up (OTA, 1991). Many of the components of oil are readily biodegradable in nature (Atlas, 1981, 1984; Prince 1993). Bioremediation is a safe cleanup method for marine oil spills (Prince and Atlas, 2016).

Studies on the British Petroleum oil spill reported injection of approximately 500 000 tons of gaseous hydrocarbons into the ocean and the gaseous emissions constituted 40% of the total hydrocarbon discharge causing tremendous atmospheric pollution (Joye et al., 2011). Many researchers have studied various aspects of the tragic oil spill of Exxon Valdez in 1989, the use of bioremediation (Atlas & Bragg 2009; Bragg et al. 1994; McDonnel 1992; Peterson et al. 2003; Pritchard et al. 1992) and the influence of temperature on biostimulation of marine oil spill (Coulon et al., 2007).

In-situ bioremediation was found to control many undesirable impacts of amendments on environment by conventional treatment methods (Brown et al, 1998; Franzetti et al, 2006; Joseph, 1998; Menendez-Vega et al., 2007; Volkering et al., 1997). Presence and activity of hydrocarbon degrading microorganisms were reported along the affected shorelines (Medina-Bellver et al, 2005). Researchers used fertilizers for bioremediation of marine oil spill and found it to be effective as the fertilizers rich in nitrate and phosphate provided nutrients for the oil degrading microorganisms (Gallego et al., 2008; Xu et al, 2005). Dominant genera observed in the marine water are Pseudomonas spp. and Bacillus spp. (Chikere et al., 2016). Catechol 2, 3 dioxygenases, a group of enzymes play important role in natural attenuation processes of hydrocarbon contaminated environment (Sierra-García et al., 2014). Comprehensive treatment of petroleum hydrocarbon by eventual manipulation of factors affecting bioremediation is technically and economically feasible (Adams et al., 2015).

Beeswax, a natural wax produced by honeybees, is used as a biostimulant for bioremediation of hydrocarbon in the present study. One kg of beeswax can store 22 kg honey (Coggshall and Morse, 1984). India accounts for the largest beeswax production of 22 000 tons, which is 33% of the global production (Sergeeva, 2017). Beeswax can absorb oil up to 20 times its weight. It contains nitrogen, phosphorus and potassium which are used as nutrient source for the bacteria. It consists of 15% hydrocarbon, 8% free acids remaining esters. The melting point ranges from 62 °C to 64 °C and density at 15 °C ranges from 958 to 970 kg/m3. Bioaugmentation could employ organisms that degrade hydrocarbons to be encapsulated in wax to form organism-containing wax microshells which are used for removing oil spills ( JUSTIA, 2018). Bioremediation can be an effective, environmentally benign means of remediating oil spill in the marine water (Mathew et al., 2019).

2 Study area and sample collection

The marine sample was collected offshore of Besant Nagar beach, Chennai, India. Composite grab sampling was used to collect 10 L of sample in a clean plastic container. The site of sample collection was devoid of any immediate effluent plume from local discharge. The sample was collected during summer when the Dissolved Oxygen (DO) is lowest in order to prove the suitability of beeswax in bioremediation of marine oil spill even in the worst scenario. The DO and pH of the sample was analysed on the same day of collection. The sample was stored at 4 °C for later analysis.

3 Methodology

A lab-scale experiment to validate the effectiveness of beeswax as a biostimulant in the bioremediation of marine oil spill was carried out using diesel oil. During combustion, diesel oil produces approximately 13% more CO2 compared to petrol.

The collected marine water sample with diesel oil and beeswax as a nutrient source was taken as the treatment and the corresponding control consisted of marine water sample with diesel oil and without beeswax. The glass beakers with sample for the control and treatment were setup as shown in Figure 1. Six samples each was used for treatment and control. Three samples were used for the analysis of Diesel Range Organics (DRO) corresponding to 5th, 10th and 15th day and the other three samples for parameters such as pH, DO, nitrate, phosphate and microbial count. The chemical formula for diesel oil ranges from C10H20 to C15H28, DRO is a good indicator of diesel content as it corresponds to the range of hydrocarbon from C10 to C28 ( API, 1994).

thumbnail Fig. 1

Experimental Setup.

Initial characterisation of the sample was carried out for vital parameters. 500 mL marine sample, 15 mL diesel oil and 5 g beeswax as pellets were added to the treatment beaker while no beeswax was added to the control. Vital parameters such as DO, pH, nitrate, phosphate, and total microbial count were analysed at intervals of 5 days for 15 days. All analyses were in accordance with the American Public Health Association ( APHA, 2005) standard procedure. In addition, DRO was also analysed during the same interval. DRO was analysed using Gas Chromatography-Mass Spectrometry (GC-MS). Another two samples were used for the analysis of oil content in the control and treatment at the end of the experiment to show the effective removal of diesel oil by evaporating the sample and measuring the remaining oil content using Soxhlet Extraction Method (Standard Methods American Water Works Association 5520 part D). Oil content was also analysed initially in the raw marine sample to determine the presence of any oil content. Average of three samples was obtained and represented graphically.

4 Results and discussion

The values of various parameters obtained in the experimental study is tabulated (Tab. 1). Significant reduction in DRO and oil content was observed in treatment compared to control after 15 days of experiment.

Table 1

Values of various parameters obtained in the experiment.

4.1 pH

The pH of the samples varied between 6.64 and 7.72 in both treatment and control (Fig. 2). The optimal pH for the growth of microorganism to degrade hydrocarbon ranges from 6 to 8 (Leahy & Colwell, 1990). The pH was within optimal range for the degradation of oil by microbes.

thumbnail Fig. 2

Temporal variation of pH.

4.2 Dissolved oxygen

The initial DO of marine water sample was 6.5 mg/L which correlates with the DO of marine water at 35 °C. The oil degrading bacteria that utilise oil as their carbon source are mostly aerobic and require DO for cellular respiration. The DO continues to reduce as no aeration is given to both the treatment and control. The DO in treatment reduces steadily which corresponds to oxygen consumption by aerobic oleophilic bacteria signifying the degradation of oil. (Fig. 3). At the end of 15-day experiment, the DO reduced to 4.9 mg/L which is adequate for the growth of microbes. In control the DO is lower than treatment initially which indicates the high oil content that does not actively degrade as in treatment, thus limits the oxygen transfer from the atmosphere to the water.

thumbnail Fig. 3

Temporal variation of DO content.

4.3 Nutrients – Nitrate and Phosphate

The beeswax added after initial characterization of the marine water sample is the source of nitrate and phosphate which are essential nutrients for the growth of indigenous microbes. The sample had an initial nitrate content of 1.285 mg/L (Fig. 4). After the addition of beeswax, the nitrate reduced significantly in the treatment within 5 days and the nitrate concentrations for 10th and 15th day were below detection limit (limit of detection: 1 mg/L). This is due to the rapid consumption of nitrate by the proliferating indigenous microbes and the growth rate increased by 5 folds in 5 days. Later the microbial count reduced due to the deficit of nitrate. The initial concentration of phosphate in the marine water sample was 1.5 mg/L. The addition of beeswax increased the phosphate content in the treatment initially which depleted slowly as only 1 part of phosphate is consumed for every 10 parts of nitrate. It reduced after 10th day as there was no further addition of beeswax (Fig. 5). In the control, phosphate steadily reduced and was below detection limit on the 15th day (Limit of detection: 0.2 mg/L). The ratio of nitrate to phosphate required for the optimal growth of bacteria is 10:1.

thumbnail Fig. 4

Temporal variation of nitrate concentration.

thumbnail Fig. 5

Temporal variation of phosphate concentration.

4.4 Total Microbial Count

The dominant species of bacteria present in marine sample are Bacillus spp. and Pseudomonas spp. Microbial count measured as Colony Forming Units (CFU) increased from 410 to 2200 CFU/mL (Fig. 6) in the treatment which is a five-fold increase during the initial 5 days due to the abundance of nutrients from beeswax and the presence of DO in the sample but after 5th day, the microbial population reduced slowly in the treatment. On the other hand, it reduced very rapidly in the control and was 70 CFU/mL on 15th day as the nutrient source and dissolved oxygen was limiting. The nitrate and phosphate are consumed by the bacteria for their growth and metabolism. The aerobic bacteria consume DO for their cellular respiration and oil as their carbon source. The significant difference in the microbial count in treatment and control indicates the importance of nutrients for the growth of microbes which could be supplemented by addition of biostimulant such as beeswax. Hence optimal nutrient level by insitu biostimulation aids in the bioremediation of marine oil spill.

thumbnail Fig. 6

Temporal variation of microbial count.

4.5 Diesel Range Organics

Diesel Range Organics (DRO) is used as a specific indicator of diesel oil in marine water. It was found to reduce significantly in the treatment to 98 ppm after 15 days whereas in the control it reduced only to 365 ppm (Fig. 7). The reduction was more prominent in treatment due to the profuse growth of oleophilic microbes resulting from the addition of biostimulant namely beeswax leading to the bioremediation of diesel oil.

thumbnail Fig. 7

Temporal variation of Diesel Range Organics.

4.6 Oil content

The oil content in the initial marine water sample, measured using soxhlet extraction method, was below detection limit. 15 mL of diesel oil was added to marine water in treatment and control. The oil content reduced to 2 mL and 6.2 mL in the treatment and control respectively after 15 days of treatment (Fig. 8). The reduction in oil content was measured by evaporating the sample in a rotary evaporator. The treatment has a removal efficiency of 87% while in control only 59% oil removal was achieved. In control, the hydrocarbons in oil can undergo phase transformation by evaporation, dissolution and dispersion. It results in the formation of aerosols which could lead to smog and their presence in the atmosphere may cause global warming thus effect the air quality. Studies by Butler et al. (1976) showed that 25% of the crude oil was evaporated naturally within 10 days. The components of oil could accumulate in food chain thus adversely affecting the aquatic environment and human health. Hence it is important to remediate marine oil spill.

thumbnail Fig. 8

Reduction in Oil Content during the experiment.

5 Conclusion

Bioremediation is an effective technique in the clean-up of petrochemical spills because it is a process of naturally converting petrochemicals into non-toxic by-products without any further local environmental disruption using microorganisms. Beeswax, a biostimulant, provides bacteria the nutrients required for its growth and metabolism. The microbes use hydrocarbon in oil as the carbon source while dissolved oxygen is used for the cellular respiration. Nitrate and phosphate are limiting in marine environment which needs to be supplemented for the rapid growth of microbes. In the present study, the addition of beeswax resulted in five-fold increase in the microbial count by the consumption of nutrients in beeswax. The experimental study conducted on the bioremediation of marine oil spill using beeswax achieved 87% removal of oil in 15 days while only 59% was removed in control. The diesel range organics reduced more in treatment than control. The removal of oil in the control is mainly due to evaporation, dissolution and sedimentation which can cause atmospheric pollution, global warming and climate change, whereas in treatment the hydrocarbon is consumed by oleophilic microbes without producing any harmful by-products. Hence bioremediation is advantageous over conventional methods, in terms of pollution abatement, cost effectiveness, insitu and environmentally benign treatment.

References

  • Adams G.O., Fufeyin P.T., Okoro S.E., Ehinomen I. (2015) Bioremediation, Biostimulation and Bioaugmention: A Review, Int. J. Environ. Bioremediat. Biodegrad. 3, 1, 28–39. [Google Scholar]
  • APHA. (2005) Standard Methods for Examination of Water and Wastewater, 21st ed., American Public Health Association/American Water Works Association/Water Environment Federation, Washington DC, USA. [Google Scholar]
  • API (American Petroleum Institute) Health and Environmental Sciences Department. (1994) Interlaboratory study of three methods for analyzing petroleum hydrocarbons in soils: diesel-range organics (DRO), gasoline-range organics (GRO), petroleum hydrocarbons (PHC), American Petroleum Institute Publications - Series: 4599, Washington, DC, USA. [Google Scholar]
  • Atlas R.M. (1981) Microbial degradation of petroleum hydrocarbons: An environmental perspective, Microbiol. Rev. 45, 1, 180–209. [PubMed] [Google Scholar]
  • Atlas R.M. (ed.) (1984) Petroleum Microbiology, Macmillan Publishing Company, New York. [Google Scholar]
  • Atlas R., Bragg J.R. (2009) Bioremediation of marine oil spills: when and when not – the Exxon Valdez experience, Microbial Biotechnol. 2, 213–221. [Google Scholar]
  • Bragg J.R., Prince R.C., Harner E.J., Atlas R.M. (1994) Effectiveness of bioremediation for the Exxon Valdez oil spill, Nature 368, 413–418. [Google Scholar]
  • Brown J.L., Syslo J.L., Yi-Hua L.L., Getty S.L., Ve-Muri R.L., Nadeau R.L. (1998) On-site treatment of contaminated soils: An approach to bioremediation of weathered petroleum compounds, J. Soil Contam. 7, 6, 773–800. [CrossRef] [Google Scholar]
  • Butler J.N., Morris B.F., Sleeter T.D. (1976) The Fate of Petroleum in the Open Ocean, in: Proceedings of the Symposium: Sources, Effects and Sinks of Hydrocarbons in the Aquatic Environment. Washington D.C August 9-11, The American Institute of Biological Sciences, Arlington VA, pp. 287–297. [Google Scholar]
  • Chikere C.B., Okoye A.U., Okpokwasili G.C. (2016) Bacterial community dynamics of nutrient enhanced oil-polluted sediment, Nigerian J. Microbiol. 30, 1, 3281–3294. [Google Scholar]
  • Coggshall W.L., Morse R.A. (1984) Beeswax production, harvesting, processing and products, Wicwas Press, Ithaca, New York. [Google Scholar]
  • Coulon F., McKew B.A., Osborn A.M., McGenity T.J., Timmis K.N. (2007) Effects of temperature and biostimulation on oil-degrading microbial communities in temperate estuarine waters, Environ. Microbiol. 9, 1, 177–186. [CrossRef] [PubMed] [Google Scholar]
  • Franzetti A., Gennaro P.D., Bevilacqua A., Papacchini M., Bestetti G. (2006) Environmental features of two commercial surfactants widely used in soil remediation, Chemosphere 62, 9, 1474–1480. [PubMed] [Google Scholar]
  • Gallego J.R., Menéndez-Vega D., González-Rojas E., Sánchez J., García-Martínez M.J., Llamas J.F. (2008) Oleophilic fertilizers and bioremediation: A new perspective, in: Modern multidisciplinary applied microbiology: Exploiting microbes and their interactions, Wiley-VCH, Badajoz, Spain, pp. 551–555. [Google Scholar]
  • JUSTIA patents. (2018) https://patents.justia.com/patent/5807724 (accessed on 15th June 2018). [Google Scholar]
  • Joseph A.R. (1998) Degradation of petroleum hydrocarbons with organisms encapsulated in wax, USPTO. https://patentimages.storage.googleapis.com/ff/71/50/33e04b54a07a68/US5807724.pdf (accessed on 15th June 2018). [Google Scholar]
  • Joye S.B., MacDonald I.R., Leifer I., Asper V. (2011) Magnitude and oxidation potential of hydrocarbon gases released from the BP oil well blowout, Nat. Geosci. 4, 3, 1–5. [Google Scholar]
  • Leahy J.G., Colwell R.R. (1990) Microbial degradation of hydrocarbons in the environment, Microbiol. Rev. 54, 3, 305–315. [PubMed] [Google Scholar]
  • Mathew R.M., Lavanya V., Rasiga S., Abraham M. (2019) Bioremediation of marine oil spill using beeswax, Indian J. Geo-Marine Sci. 48, 8, 1227–1231. [Google Scholar]
  • McDonnel J.A. (1992) The U.S. Army Corps of Engineers Response to the Exxon Valdez Oil Spill, U.S. Army Corps of Engineers, Fort Belvoir, Virginia. [Google Scholar]
  • Medina-Bellver J.I., Marín P., Delgado A., Rodríguez-Sánchez A., Reyes E., Ramos J.L., Marques S. (2005) Evidence for in situ crude oil biodegradation after the Prestige oil spill, Environ. Microbiol. 76, 773–779. [CrossRef] [PubMed] [Google Scholar]
  • Menendez-Vega D., Gallego J.L.R., Pelaez A.I., Fernandez De Cordoba G., Moreno J.H., Muñoz D., Sánchez J. (2007) Engineered in situ bioremediation of soil and groundwater polluted with weathered hydrocarbons, Eur. J. Soil Biol. 43, 5, 310–321. [Google Scholar]
  • OTA (Office of Technology Assessment) U.S. Congress. (1990) Coping with an Oiled Sea: An Analysis of Oil Spill Response Technologies. OTA-BP-O-63, U.S. Government Printing Office, Washington, DC [Google Scholar]
  • OTA (Office of Technology Assessment) U.S. Congress. (1991) Bioremediation of Marine Oil Spills: An Analysis of Oil Spill Response Technologies. OTA-BP-O-70, U.S. Government Printing Office, Washington, DC, US. [Google Scholar]
  • Peterson C.H., Rice S.D., Short J.W., Esler D., Bodkin J.L., Ballachey B.E., Irons D.B. (2003) Long-term ecosystem response to the Exxon Valdez oil spill, Science 302, 5653, 2082–2086. [Google Scholar]
  • Prince R.C. (1993) Petroleum spill bioremediation in marine environments, Crit. Rev. Microbiol. 19, 4, 217–242. [CrossRef] [PubMed] [Google Scholar]
  • Prince R.C., Atlas R.M. (2016) Bioremediation of Marine Oil Spills, in: Consequences of microbial interactions with hydrocarbons, oils, and lipids: biodegradation and bioremediation. Handbook of Hydrocarbon and Lipid Microbiology, Steffan R. (ed.), Springer, Cham. [Google Scholar]
  • Pritchard P.H., Mueller J.G., Rogers J.C., Kremer F.V., Glaser J.A. (1992) Oil spill bioremediation: experiences, lessons and results from the Exxon Valdez Oil Spill in Alaska, Biodegradation 3, 2–3, 315–335. [Google Scholar]
  • Sergeeva A. (2017) Index box: Which country produces the most beeswax in the World? [Google Scholar]
  • Sierra-García I.N., Correa Alvarez J., Pantaroto de Vasconcellos S., Pereira de Souza A., dos Santos Neto E.V., de Oliveira V.M. (2014) New Hydrocarbon Degradation Pathways in the Microbial Metagenome from Brazilian Petroleum Reservoirs, PLoS ONE 9, 2, e90087. [CrossRef] [PubMed] [Google Scholar]
  • Volkering F., Breure A.M., Rulkers W.H. (1997) Microbiological aspects of surfactant use for biological soil remediation, Biodegradation 8, 6, 401–417. [Google Scholar]
  • Xu R., Lau A.N., Lim Y.G., Obbard J.P. (2005) Bioremediation of oil-contaminated sediments on an inter-tidal shoreline using a slow-release fertilizer and chitosan, Mar. Pollut. Bull. 51, 8–12, 1062–1070. [PubMed] [Google Scholar]
  • Zobell C.E. (1973) Microbial degradation of oil: present status, problems and perspectives, in: The microbial degradation of oil pollutants, Ahearn D.G., Meyers S.P. (eds.), Pub. No. LSU-SG-73-0, Center for Wetlands resources, LSU, pp. 3–15. [Google Scholar]

All Tables

Table 1

Values of various parameters obtained in the experiment.

All Figures

thumbnail Fig. 1

Experimental Setup.

In the text
thumbnail Fig. 2

Temporal variation of pH.

In the text
thumbnail Fig. 3

Temporal variation of DO content.

In the text
thumbnail Fig. 4

Temporal variation of nitrate concentration.

In the text
thumbnail Fig. 5

Temporal variation of phosphate concentration.

In the text
thumbnail Fig. 6

Temporal variation of microbial count.

In the text
thumbnail Fig. 7

Temporal variation of Diesel Range Organics.

In the text
thumbnail Fig. 8

Reduction in Oil Content during the experiment.

In the text

Les statistiques affichées correspondent au cumul d'une part des vues des résumés de l'article et d'autre part des vues et téléchargements de l'article plein-texte (PDF, Full-HTML, ePub... selon les formats disponibles) sur la platefome Vision4Press.

Les statistiques sont disponibles avec un délai de 48 à 96 heures et sont mises à jour quotidiennement en semaine.

Le chargement des statistiques peut être long.