Regular Article
Phase behavior and miscible mechanism in the displacement of crude oil with associated sour gas
Research Institute of Petroleum Exploration and Development, PetroChina, 20 Xueyuan Road, Haidian, Beijing 100083, China
* Corresponding author: hecongge1988@163.com
Received:
3
January
2019
Accepted:
11
April
2019
The re-injection of associated sour gas, with high H2S and CO2 content, into the reservoir is proposed to be an effective development method due to its low investment cost and high oil recovery. The aim of this work is to present the phase behavior and miscible mechanism of crude oil displaced by associated sour gas. Based on the equation of state and the phase equilibrium theory, the phase behavior of crude oil mixed with various gases (associated sour gas, H2S, CO2 and CH4) have been analyzed. Then, the miscibility of associated sour gas was determined by calculating its Minimum Miscible Pressure (MMP) and the effect of sour component fraction on miscibility was evaluated. Moreover, a series of numerical simulations modeling 1D slim-tube were conducted using a compositional simulator to study the miscible mechanism in the displacement of crude oil with associated sour gas. The results show that the injection of H2S can reduce the bubble point pressure of crude oil and therefore is beneficial to prevent the crude oil degassing; nevertheless, the injection of CO2 has little effect on it. The miscible ability of associated sour gas decreases as its sour component fraction decreases. It is observed that the crude oil displaced by associated sour gas and sweet gas both show a combined condensing/vaporizing mechanism, with miscible zone in the middle of transition zone. However, the vaporizing-gas drive mechanism is slightly stronger than the condensing-gas drive mechanism during the displacement by associated sour gas while is significantly stronger during the displacement by sweet gas.
© C. He et al., published by IFP Energies nouvelles, 2019
This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
1 Introduction
Gas injection to improve oil recovery has been researched and successfully applied in many oil fields all over the world for almost one half century (Arne et al., 2000; Chen, 1995; Knut and Lars, 2002; Murty and Al-Khayat, 1989; Teletzke et al., 2005; Zhang et al., 2013). Gas injection not only is a pressure maintenance program, which can support the reservoir pressure and thereby increase the rate of oil production, but also is an important way for enhanced oil recovery by achieving miscibility (Tang et al., 2001; Zakaria, 2011; Zhu et al., 2015). Recently, the most common injection mediums are hydrocarbon, CO2, N2 and flue gas (Chen et al., 2011; Kulkarni and Rao, 2005; Meng et al., 2018). Guo (Guo et al., 2000) researched the influence of injection gas (CO2, N2, CH4 and flue gas) on physical behavior of crude oil.
The mechanisms of miscibility have been extensively discussed in literature (Johns et al., 1994, Li et al., 2006; Tang et al., 2004; 2005). Traditionally, the crude oil displaced by injected gas may achieve miscibility in two ways: condensing-gas drive mechanism and vaporizing-gas drive mechanism. When the gas is rich in intermediate component, the intermediate component in the gas will condense into the crude oil thus making the oil richer and richer, until it becomes rich enough to be miscible with the fresh injected gas. The vaporizing-gas drive process is shown in Figure 1a. The miscible zone of condensing-gas drive is located behind the immiscible zone (two-phase region). However, in the vaporizing-gas drive process, the intermediate component of the crude oil is stripped into the gas, which makes the gas richer and richer. Eventually, if the crude oil is rich enough, the gas becomes so enriched with the intermediate component that it becomes miscible with the original crude oil. The condensing-gas drive process is shown in Figure 1b. The miscible zone of vaporizing -gas drive is located on the front of the immiscible zone. The crude oil displaced by enriched gas can display features of both condensing and vaporizing drives (Stalkup, 1987; Zick, 1986). They pointed out that above an apparent minimum miscibility pressure, the condensing/vaporizing mechanism can generate displacements that are effectively miscible, although true miscibility may not actually be developed.
![]() |
Fig. 1 Classic miscible mechanism schematic. |
The re-injection of associated sour gas, with high H2S and CO2 content, are being conducted in many reservoirs, such as Tengiz oil field in western Kazakhstan (Sabyrzhan et al., 2010). On the one hand, the re-injection of associated sour gas can reduce the investment cost as the desulphurization equipment is not required. On the other hand, it can maintain the reservoir pressure and realize miscibility, thus achieving high oil recovery (Xu et al., 2015; Zhang et al., 2016). High H2S and CO2 content in associated sour gas may make the phase behavior and miscible mechanism different from usually injected gas, such as pure CO2, pure CH4 and enriched gas. The main focus of this paper is to investigate the phase behavior and miscible mechanism of crude oil displaced by associated sour gas. In this paper, the phase behavior of crude oil mixed with various gases (associated sour gas, H2S, CO2 and CH4) was firstly analyzed based on the equation of state and the phase equilibrium theory. Then, the miscibility of associated sour gas was determined and the effect of sour component fraction on miscibility was evaluated. Moreover, a series of numerical simulations modeling 1D slim-tube were conducted to present the miscible mechanism in the displacement of crude oil with associated sour gas. On the basis, the effect of pressure and injected gas composition (associated sour gas, sweet gas and CH4) on miscibility was analyzed in detail.
2 Phase behavior analysis
The crude oil of K oil field in Kazakhstan was divided into nine pseudo-components according to its characterization. The composition of crude oil and associated sour gas are given in Table 1. The C20+ fraction of the crude oil has a molar mass about 437.91 g/mol and density about 907 kg/m3. Table 1 shows that the crude oil is sour containing approximately 14.69% H2S and 4.12% CO2. The associated sour gas, which is re-injected into the reservoir to enhance oil recovery, contains 17.42% H2S and 4.92% CO2. The bubble point of crude oil is about 28 MPa at the reservoir temperature of 373.15 K.
The pseudo-composition of crude oil and associated sour gas and the critical parameters of EOS.
Based on the software of Eclipse PVTi developed by Schlumberger, the critical parameters of EOS for each component are obtained through fitting PVT experimental results. Figure 2 shows that the fitting results coincide with the experimental data very well. The critical parameters of EOS for each component are presented in Table 1.
![]() |
Fig. 2 The fitting of PVT experimental results. |
Based on the phase equilibrium model (Chueh and Prausnitz, 1967; Obut et al., 1986; Yang and Wei, 2004) and SRK equation of state (Soave, 1972), the phase behavior of crude oil mixed with various gases (associated sour gas, H2S, CO2 and CH4) was performed as shown in Figure 3. The injection gas mole fraction (f) is 0.3, which is defined as the mole ratio of injection gas and crude oil. Figure 3 shows that the critical point of crude oil after injecting gas moves closer to original reservoir conditions (the original reservoir temperature and pressure are 373.15 K and 77.8 MPa respectively). For example, the critical temperature and pressure of crude oil are 592 K and 28.4 MPa and they move to 518 K and 33.1 MPa after injecting associated sour gas. It means that the crude oil becomes more volatile after injecting gas. Figure 3 also indicates that the two-phase region becomes narrower after injecting H2S and becomes wider after injecting CH4. Whereas, the two-phase region changes little after injecting associated sour gas and injecting CO2. For instance, the bubble point pressure of crude oil decreases from 28 MPa to 21.8 MPa after injecting H2S and increases to 37.8 after injecting CH4 at the reservoir temperature. The bubble point pressure of crude oil after injecting associated sour gas and injecting CO2 are 30.1 MPa and 29.2 MPa at the reservoir temperature, respectively. From the analysis, it is demonstrated that the injection of H2S can reduce the bubble point pressure of crude oil and therefore is beneficial to prevent the crude oil degassing; nevertheless, the injection of CO2 has little effect on it.
![]() |
Fig. 3 The influence of gas injection on P–T phase diagram (injection gas mole fraction f = 0.3). |
The influence of injection gas mole fraction on the phase behavior of crude oil is shown in Figure 4. It indicates that the critical point of crude oil moves closer to original reservoir conditions when the injection gas mole fraction is greater; that is, the greater the injection gas mole fraction, the crude oil becomes more volatile. The green line within the two phase region in Figure 4 represents constant liquid saturation and its value is 50%. It can be easily found in Figure 4 that the pressure differentials between the bubble point pressure and the pressure crossing the 50% liquid saturation line at the reservoir temperature are 11.9 MPa, 8.5 MPa and 4.8 MPa with the injection gas mole fraction of 0, 0.3 and 0.5, respectively. It means the shrinkage of crude oil becomes higher when the injection gas mole fraction is greater. Higher shrinkage is caused by a greater concentration of intermediate hydrocarbons in crude oil due to more gas injection.
![]() |
Fig. 4 The influence of injection gas mole fraction on P–T phase diagram. |
3 Miscible mechanism analysis
3.1 Minimum Miscible Pressure (MMP)
Minimum Miscible Pressure (MMP) is a key parameter in the design of gas flooding. Recently, there are several methods available to calculate MMP. Experimental methods include slim-tube experiment, rising bubble method and vanishing interfacial tension method (Zhang et al., 2016). The rising bubble method and the vanishing interfacial tension method do not have the proper interactions of flow with phase behavior necessary to develop multi-contact miscibility. Slim-tube experiment, which uses actual reservoir fluids, can provide a reliable estimate and now is regarded as the standard procedure for predicting MMP. The crude oil of K oilfield displaced by the associated sour gas in the slim-tube is conducted at various pressures. The recovery at 1.2 PV injectant against the pressure is plotted in Figure 7. It shows that the MMP of the associated sour gas is 28 MPa. Since slim-tube experiment is expensive and time consuming in practice, we resort to the analytical method, such as mixing-cell method (Abiodun et al., 2012), to analyze the effect of injection gas composition on MMP. In mixing-cell method, repeated contacts of equilibrium gas and oil with fresh gas and oil are made until the key tie line is found. The advantage of the mixing-cell method is that it is very fast and the result also is reliable. The MMP of the associated sour gas calculated by mixing-cell method is 27.85 MPa. Compared to the slim-tube experiment result of 28 MPa, a relative error of 0.5% supports the reliability and correctness of the mixing-cell method. On the basis, the MMP of different injection gas composition were calculated by mixing-cell method to determine their miscible ability and the result is shown in Figure 5. From Figure 5, it can be easily found that the miscible ability decrease in the following order: H2S, C2H6, associated sour gas, CO2 and CH4. The MMP of H2S has the minimum value of 21 MPa and that of CH4 has the maximum value of 44 MPa. As the associated sour gas consists mainly of 59.03% CH4 and contains 17.42% H2S and 4.92% CO2, the miscible ability is in between CH4 and H2S.
![]() |
Fig. 5 The MMP of different injection gas composition calculated by the mixing-cell method. |
Understanding the impact of the gas compositional changes on the MMP is essential to optimal design of field-wide pressure management. In order to evaluate the effect of sour components (H2S and CO2) in the associated sour gas on MMP, the MMP of various levels of sour gas fraction were calculated by the mixing-cell method and the result is shown in Figure 6. A sour component fraction of 1 means the injectant is the original associated sour gas while a sour component fraction of zero means the corresponding sour component is excluded completely and other components are normalized. Figure 6 shows that the lower the sour gas component fraction, the greater the MMP. In other words, the miscible ability of associated sour gas decreases with the decrease of its sour component fraction. Re-injecting associated sour gas directly without eliminating its sour component is more likely to achieve miscible displacement. It also can be found that eliminating H2S from the original associated sour gas has greater effect on miscible ability than eliminating CO2. This is due to the fact that H2S has greater miscible ability and larger content in the associated sour gas of K oilfield than CO2.
![]() |
Fig. 6 The effect of sour component fraction on MMP calculated by the mixing-cell method. |
3.2 Miscible mechanism of associated sour gas injection
To gain understanding about the miscible mechanism of sour gas injection, we resort to slim-tube simulation based on the Eclipse compositional simulator (E300) developed by Schlumberger. The composition of components and their critical parameters of EOS shown in Table 1 are inputted into the Eclipse model. The grid size is 1000 × 1 × 1 and the corresponding block dimensions are 0.001 m, 0.01 m and 0.01 m. The injector is located at the first grid and the producer is located at the last grid. The porosity is 6% and the permeability is 10 × 10−3 μm2. The pressure drop across the slim-tube is ignored and the capillary pressure between oil and gas was zero. The gas was injected at the rate of 0.024 m3/h. Before conducting slim-tube displacement experiments to investigate the miscible mechanism of sour gas injection, the Eclipse model was validated by comparing the oil recovery between slim-tube experiment data and simulation results as shown in Figure 7. It shows that the oil recovery obtained by Eclipse model is consistent with that of slim-tube experiment under the same pressure, which verifies the reliability of the Eclipse model.
![]() |
Fig. 7 The comparison of recovery between slim-tube experiment data and simulation results. |
Figures 8–10 show the profiles within the slim-tube for the displacement by associated sour gas with 0.4 PV of associated sour gas injected at a pressure 28.2 MPa (just above its MMP). Figure 8a shows that three zones that are gas zone, transition zone and oil zone are formed in the slim-tube. Gas zone and oil zone only contain a single phase, that is, vapor phase or liquid phase. Therefore, the interfacial tension in these zones is zero. Transition zone contains vapor phase and liquid phase. As can be seen in Figure 8b, the interfacial tension decreases, reaches a minimum and then increases down the slim-tube in the transition zone. The middle position of the transition zone, where the interfacial tension reaches minimum, is closest to miscibility. The mechanism of crude oil displaced by associated sour gas is not either the condensing-gas drive mechanism or the vaporizing-gas drive alone. Instead, it shows a combined condensing/vaporizing type. The middle position seems to be the leading edge of vaporizing-gas drive mechanism and be the trailing edge of condensing-gas drive mechanism. The middle position divided the transition zone into two regions: vaporizing zone and condensing zone. Figure 8b also shows that the vaporizing zone is slightly larger than the condensing zone. The vaporizing zone extends from grid 327 to grid 397, a total of 70 grids, while the condensing zone extends from grid 398 to grid 458, a total of 60 grids. It means that though the displacement of crude oil by associated sour gas is a combined condensing/vaporizing mechanism, the vaporization part of mechanism is slightly stronger than the condensation part of mechanism. The viscosity and density of vapor phase and liquid phase are closest approach each other but don’t converge to the same value at the point where the interfacial tension reaches minimum as shown in Figure 9. It should be pointed out that even though the displacement pressure is above the MMP, the interfacial tension at the middle position of the transition zone is 0.001, not zero. In other words, the true miscibility was not achieved. Instead, it is kind of near miscibility. This is the reason why the viscosity and density of vapor phase and liquid phase at the middle position are very close to each other but don’t converge to the same value.
![]() |
Fig. 8 Saturation and interfacial tension profile within the slim-tube for the displacement of crude oil by associated sour gas. |
![]() |
Fig. 9 Viscosity and density profile within slim-tube for the displacement of crude oil by associated sour gas. |
Components profiles within slim-tube as shown in Figure 10 indicate the formation process of the combined condensing/vaporizing mechanism during the displacement of crude oil by associated sour gas. The light intermediates, such as C2–6, H2S and CO2, condense into the crude oil as the associated sour gas contact the crude oil. This can be reasonably extrapolated from Figure 10b which shows that the mole fraction of light intermediates is higher than that of the original crude oil. Meanwhile, the middle intermediates, such as C7–20, vaporize into the vapor as shown in Figure 10c that the mole fraction of middle intermediates is lower than that of the original crude oil. At first the condensation of the light intermediates causes the oil lighter and then the vaporization of the middle intermediates causes the oil heavier. This is the reason why the miscibility happened in the middle of transition zone.
![]() |
Fig. 10 Components profiles within slim-tube for the displacement of crude oil by associated sour gas. |
3.3 The effect of pressure on miscibility
In order to investigate the effect of pressure on miscibility, the displacements of crude oil with associated sour gas were simulated in slim-tube at various pressures. Figure 11a shows the profiles within slim-tube after 0.4 PV of associated sour gas was injected at pressure of 33 MPa. As can be seen in Figure 11a, the displacement of crude oil by associated sour gas at pressure of 33 MPa also shows a combined condensing/vaporizing mechanism, very similar to that of at pressure of 28.2 MPa, but the transition zone at pressure of 33 MPa is much smaller than that of at pressure of 28.2 MPa. For instance, the transition zone extends from grid 328 to grid 458, a total of 130 grids, at pressure of 28.2 MPa; nevertheless, it just extends from grid 357 to grid 426, a total of 69 grids, at pressure of 33 MPa. It is also worth noting that the interfacial tension at the middle position of the transition zone is very small but not zero when the pressure is 33 MPa, similar to that of at pressure of 28.2 MPa. That is, the true miscibility was not achieved even though the displacement pressure is already above the MMP. The simulations result shows that the near miscibility rather than true miscibility was achieved during displacement by the combined condensing/vaporizing mechanism. Figure 11b shows that the transition zone disappeared when the pressure increased to 36 MPa, which means the injectant has become first-contact miscible with the crude oil.
![]() |
Fig. 11 The effect of pressure on miscibility with associated sour gas injection. (a) P = 33 MPa, (b) P = 36 MPa. |
3.4 The effect of injected gas composition on miscibility
In order to investigate the effect of injected gas composition on miscibility, the displacements of crude oil with different solvents were simulated in slim-tube. The associated gas is sour containing 17.42% H2S and 4.92% CO2. The sweet gas is defined as the associated sour gas with eliminating its sour component (H2S and CO2). Figure 6 shows that the MMP of sweet gas is about 31.9 MPa. Figure 12 shows the saturation and interfacial tension profile within the slim-tube for the displacement by sweet gas. These profiles, again at 0.4 PV of gas injected, were generated during the displacement with the pressure of 32.3 MPa, just above its MMP. Figure 12 indicates that the displacement of crude oil by sweet gas also shows a combined condensing/vaporizing mechanism. Unlike the associated sour gas, the vaporizing zone is significantly larger than the condensing zone during the displacement by sweet gas, that is, the vaporizing-gas drive mechanism is significantly stronger than the condensing-gas drive mechanism during the displacement by sweet gas. For instance, the vaporizing zone extends from grid 168 to grid 353, a total of 185 grids, while the condensing zone extends from grid 354 to grid 457, a total of 103 grids. Figure 5 shows that the MMP of CH4 is about 44 MPa. Figure 13 shows the saturation and interfacial tension profile within slim-tube after 0.4 PV of CH4 was injected at pressure of 44.5 MPa. It can be easily found that the displacement of crude oil by CH4 is pure condensing-gas drive mechanism.
![]() |
Fig. 12 Saturation and interfacial tension profile within slim-tube for the displacement of crude oil by sweet gas. |
![]() |
Fig. 13 Saturation and interfacial tension profile within slim-tube for the displacement of crude oil by CH4. |
4 Conclusion
The following conclusions can be summarized from the results of this work:
-
The two-phase region becomes narrower after injecting H2S and becomes wider after injecting CH4. The injection of H2S can reduce the bubble point pressure of crude oil and therefore is beneficial to prevent the crude oil degassing; nevertheless, the injection of CO2 has little effect on it.
-
The miscible ability decrease in the following order: H2S, C2H6, associated sour gas, CO2 and CH4. The miscible ability of associated sour gas decreases with the decrease of its sour component fraction. Re-injecting associated sour gas directly without eliminating its sour component is more likely to achieve miscible displacement.
-
The mechanism of crude oil displaced by associated sour gas and sweet gas both show a combined condensing/vaporizing type, with miscible zone in the middle of transition zone. Unlike the associated sour gas, the vaporizing-gas drive mechanism is significantly stronger than the condensing-gas drive mechanism during the displacement by sweet gas.
-
The transition zone decreases with increasing pressure and it would disappear when the injectant becomes first-contact miscible with the crude oil.
Acknowledgments
This work was supported by the Major Projects of China (2017ZX05030).
References
- Abiodun M., Shameem S., Habib M., Bob L. (2012) A new look at the minimum miscibility pressure (MMP) determination from slimtube measurements, Proceedings of the Eighteenth SPE Improved Oil Recovery Symposium, Oklahoma, USA, SPE 153383. [Google Scholar]
- Arne S., Norsk H., Leonid S. (2000) Gas injection in Paleo oil zone, Proceedings of SPE Annual Technical Conference and Exhibition, Dallas, Texas, SPE 62996. [Google Scholar]
- Chen H. (1995) Gas injection in the Safah field, Oman, Proceedings of SPE Middle East Oil, Bahrain, SPE 29805. [Google Scholar]
- Chen W., Tang Y., Liang T., Sun L., Liu W., Chen Z. (2011) Mechanism study of supercritical CO2’s dynamic miscible flooding process, Drill. Prod. Technol. 34, 3, 77–80. [Google Scholar]
- Chueh P.L., Prausnitz J.M. (1967) Vapour-liquid equilibria at high pressures, calculation of partial molar volume in non-polar liquid mixtures, AIChE 13, 6, 1099–1113. [CrossRef] [Google Scholar]
- Guo P., Sun L., Sun L., Li S., Peng P., Yue L. (2000) Influences of injection gas on physical behavior of crude, J. Southwest Pet. Inst. 22, 3, 57–64. [Google Scholar]
- Johns R.T., Fayers F.J., Orr F.M. (1994) Effect of gas enrichment and dispersion on nearly miscible displacements in condensing/vaporizing drives, SPE Adv. Technol. Ser. 2, 2, 26–34. [CrossRef] [Google Scholar]
- Knut U., Lars H. (2002) Miscible gas injection in fractured reservoirs, Proceedings of SPE/DOE Improved Oil Recovery Symposium, Tulsa, Oklahoma, USA, SPE 75136. [Google Scholar]
- Kulkarni M.M., Rao D.N. (2005) Experimental investigation of miscible secondary gas injection, Proceedings of SPE Annual Technical Conference and Exhibition, Dallas, Texas, USA, SPE 95975. [Google Scholar]
- Li M., Shan W., Liu X., Shang G. (2006) Laboratory study on miscible oil displacement mechanism of supercritical carbon dioxide, Acta Petrolei Sinica 27, 3, 80–83. [CrossRef] [Google Scholar]
- Meng F., Lei Q., Sun Y., He D. (2018) Law of CO2 immiscible front movement in low-permeability oil reservoir, J. Southwest Pet. Univ. (Sci. Technol. Ed.) 40, 3, 121–128. [Google Scholar]
- Murty C., Al-Khayat S. (1989) Gas injection in a saturated oil reservoir, Proceedings of SPE Middle East Oil Technical Conference and Exhibition, Manama, Bahrain, SPE 17991. [Google Scholar]
- Obut S.T., Ertekin T., Geisbrecht R.A. (1986) A versatile phase equilibrium package for compositional simulation, Proceedings of 56th California Regional Meeting of the Society of Petroleum Engineers, Oakland, CA, SPE 15083. [Google Scholar]
- Sabyrzhan D., Aizada A., Dave B., Mike S., Greg K., Tayo F., Phil B. (2010) Tengiz sour gas injection project, Proceedings of Caspian Carbonates Technology Conference, Atyrau, Kazakhstan, SPE 139851. [Google Scholar]
- Soave G. (1972) Equilibrium constants from a modified Redlich-Kwong equation of state, Chem. Eng. Sci. 27, 1197–1203. [Google Scholar]
- Stalkup F.I. (1987) Displacement behavior of the condensing/vaporizing gas drive process, Proceedings of 62nd Annual Technical Conference and Exhibition, Dallas, TX, SPE 16715. [Google Scholar]
- Tang Y., Sun L., Xiong J., Guo P., Wang Z., Zhang X. (2001) Study on the simulation calculation of complete p-x phase diagram in miscible gas injection, J. South Pet. Inst. 23, 3, 40–43. [Google Scholar]
- Tang Y., Sun L., Zhou Y., Li S., Guo P., Li Y. (2004) On evaluation method of miscible gas-flooding mechanism, Xinjiang Pet. Geol. 25, 4, 414–417. [Google Scholar]
- Tang Y., Sun L., Zhou Y., Li S., Sun L., Du Z. (2005) Mechanism evaluation of condensing/vaporizing miscible flooding with hydrocarbon rich gas injection, Pet. Explor. Dev. 32, 2, 133–136. [Google Scholar]
- Teletzke G.F., Patel P.D., Chen A.L. (2005) Methodology for miscible gas injection EOR screening, Proceedings of SPE International Improved Oil Recovery Conference in Asia Pacific, Kuala Lumpur, Malaysia, SPE 97650. [Google Scholar]
- Xu A., Mu L., Zhao L., Wang C. (2015) Analysis of miscibility of high sour component (H2S and CO2) content gas flooding under abnormal reservoir pressure, Proceedings of Asia Pacific Oil & Gas Conference and Exhibition, Nusa Dua, Bali, Indonesia, SPE 176591. [Google Scholar]
- Yang S., Wei J. (2004) Reservoir physics, 1st edn., Petroleum Industry Press, Beijing. [Google Scholar]
- Zakaria A. (2011) Optimizing simulation studies for miscible gas injection process using horizontal wells, Proceedings of SPE Enhanced Oil Recovery Conference, Kuala Lumpur, Malaysia, SPE 144069. [Google Scholar]
- Zhang C., Fan Z., Xu A., Zhao L., Zhao L. (2016) The influence of sour gas on MMP and the composition optimization for solution gas reinjection in volatile oil reservoir, Sci. Technol. Eng. 16, 11, 54–58. [Google Scholar]
- Zhang P., Brodie J., Daae V., Erbas D., Duncan E. (2013) BP North sea miscible gas injection projects review, Proceedings of SPE Offshore Europe Oil and Gas Conference and Exhibition, Aberdeen, UK, SPE 166597. [Google Scholar]
- Zhu L., Liao X., Zhao X., Chen Z., Chen Y., Wang H. (2015) Effects of different gases on hydrocarbon miscible displacements, J. Shaanxi Univ. Sci. Technol. 33, 5, 100–105. [Google Scholar]
- Zick A.A. (1986) A combined condensing/vaporizing mechanism in the displacement of oil by enriched gases, Proceedings of Annual Technical Conference and Exhibition, New Orleans, LA, SPE 15493. [Google Scholar]
All Tables
The pseudo-composition of crude oil and associated sour gas and the critical parameters of EOS.
All Figures
![]() |
Fig. 1 Classic miscible mechanism schematic. |
In the text |
![]() |
Fig. 2 The fitting of PVT experimental results. |
In the text |
![]() |
Fig. 3 The influence of gas injection on P–T phase diagram (injection gas mole fraction f = 0.3). |
In the text |
![]() |
Fig. 4 The influence of injection gas mole fraction on P–T phase diagram. |
In the text |
![]() |
Fig. 5 The MMP of different injection gas composition calculated by the mixing-cell method. |
In the text |
![]() |
Fig. 6 The effect of sour component fraction on MMP calculated by the mixing-cell method. |
In the text |
![]() |
Fig. 7 The comparison of recovery between slim-tube experiment data and simulation results. |
In the text |
![]() |
Fig. 8 Saturation and interfacial tension profile within the slim-tube for the displacement of crude oil by associated sour gas. |
In the text |
![]() |
Fig. 9 Viscosity and density profile within slim-tube for the displacement of crude oil by associated sour gas. |
In the text |
![]() |
Fig. 10 Components profiles within slim-tube for the displacement of crude oil by associated sour gas. |
In the text |
![]() |
Fig. 11 The effect of pressure on miscibility with associated sour gas injection. (a) P = 33 MPa, (b) P = 36 MPa. |
In the text |
![]() |
Fig. 12 Saturation and interfacial tension profile within slim-tube for the displacement of crude oil by sweet gas. |
In the text |
![]() |
Fig. 13 Saturation and interfacial tension profile within slim-tube for the displacement of crude oil by CH4. |
In the text |